sâmbătă, ianuarie 30, 2010

Error code CANON E 5




  Am văzut pe mai multe forumuri că mută lumea încearcă şi reuşeşc să reseteze imprimantele sau multifuncţionarele Canon după refillare dar cîteodată nu reuşesc să treacă de Error code E5. Ce este acest cod ?
Pe cartea tehnică a imprimantei Canon MP 210 este următoarea explicaţie :

"The FINE Cartridge may not be installed properly, or the Cartridge may not be compatible with this machine. Open the Scanning Unit (Printer Cover) and install the appropriate FINE Cartridge.

If the error is not resolved, the Print Head may be damaged. Contact your Canon Service representative. "

Dacă, spre exemplu, scoateţi din imprimanta dv. Canon scoateţi de curiozitate unul din cartuşe o să vedeţi că apare pe displeyul imprimantei acelaşi detestat cod E 5. Deci ce se poate face în acest caz ? O soluţie ar fi să scoateţi cartuşul din imprimantă şi să-i curăţiţi contactele electrice şi de pe cartuş şi din imprimantă. Dacă eroarea persistă înseamnă că cartuşul respectiv este ars şi trebuie înlocuit cu un cartuş nou.
Mai jos am descris pe scurt cîteva coduri de eroare de la imprimantele Canon Pixma :
E2-2 = No paper (ASF) 
E3-3 = Paper jam E4 = No ink 
 E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly 
 E8 = Waste ink absorber full, or platen waste ink absorber full 
 E9 = The connected digital camera / video camera does not support Camera Direct Printing E14 = The Ink cartridges whose destination are wrong 
E15 = Ink cartridge is not installed 
E16 - Ink remaining is unknown 
 E16 -E19 = Failed to scan head alignment sheet  
E22 = Carriage error 
 E23 = Paper feed error 
E24 = Purge unit error 
 E25 = ASF(cam) sensor error  
E26 = Internal temperature rise error
  E27 = Waste ink absorber full or platen waste ink absorber full 
E28 = Ink cartridge temperature rise error - 
 E29 = EEPROM error 
E33 = Paper feed position error 
 E35 15 = USB Host VBUD overcurrent error - USB 
E37 17 = Abnormal motor driver error
 E40 20 = Other hardware error 
E42 22 = Scanner error.

Alte coduri de eroare de eroare mai găsiţi şi mai jos :

An Error Message Is Displayed on the LCD/LED

If an error message is displayed on the LCD or LED, take the corresponding action described below.

An Error Message Is Displayed on the LCD (MP220 series)

Message

Action

CHECK INK

U051/U052/U053/U059

The FINE Cartridge may not be installed properly, or the Cartridge may not be compatible with this machine. Open the Scanning Unit (Printer Cover) and install the appropriate FINE Cartridge.

If the error is not resolved, the FINE Cartridge may be damaged. Contact your Canon Service representative.

CHECK INK

U075/U076

Make sure that each FINE Cartridge is installed in the correct position.

See Replacing a FINE Cartridge.

CHECK INK

U140

The FINE Cartridge may not be compatible with this machine. Install the appropriate FINE Cartridge. See Replacing a FINE Cartridge.

CHECK INK

U150

The FINE Cartridge may not be installed properly.

Open the Scanning Unit (Printer Cover) and install the FINE Cartridge properly.

If the error is not resolved, the FINE Cartridge may be damaged. Contact your Canon Service representative.

CHECK INK

U162

Ink may have run out.

The function for detecting the remaining ink level will be disabled since the ink level cannot be correctly detected.

If you want to continue printing without this function, press the Stop/Reset button for at least 5 seconds.

Canon recommends to use new genuine Canon cartridges in order to obtain optimum qualities.

Please be advised that Canon shall not be liable for any malfunction or trouble caused by continuation of printing under the ink out condition.

CHECK INK

U163

Ink has run out.

Replace the ink cartridge and close the Scanning Unit (Printer Cover).

If printing is in progress and you want to continue printing, press the Stop/Reset button for at least 5 seconds with the ink cartridge installed. Then printing can continue under the ink out condition.

The function for detecting the remaining ink level will be disabled.

Replace the empty ink cartridge immediately after the printing. The resulting print quality is not satisfactory, if printing is continued under the ink out condition.

NO PHOTOS ON CARD

There are no image data saved on the memory card that can be read by this machine.

The machine may not recognize the file if the file name or the folder path contains certain characters. Use only alphanumeric characters.

Photo data edited or processed on a computer must be printed from the computer.

REQ. SERVICE SOON

The machine has a built-in ink absorber to hold the ink used during Print Head Cleaning, for example.

This error message indicates that the ink absorber is nearly full.

Press the OK button to cancel the error so you can continue printing.

However, because printing is disabled once the ink absorber becomes completely full and until the ink absorber is replaced, you are recommended to contact your Canon service representative as early as possible. (You will need to replace a particular part of the machine.)

INCOMPATIBLE CAMERA

A communication time out occurs if an operation takes too long or if it takes too much time to send data. This may cancel printing. In such cases, disconnect and reconnect the USB cable.

When printing from a PictBridge compliant device, depending on the model or brand of your device, you may have to select a PictBridge compliant print mode on the device before connecting it to the machine. You may also have to turn on your device or select Play mode manually after connecting the device to the machine. Perform necessary operations before connecting your device referring to its instruction manual.

If the error is still not resolved, check if you can print another photograph.

UNSUPPORTED USB HUB

If a PictBridge compliant device is connected via a USB hub, remove the hub and connect it directly to the machine.

CHECK PRINTER

Turn off the machine, and unplug the power cord of the machine from the power supply. After a while, plug the power cord of the machine back in, and then turn on the machine. If the same error occurs, contact your Canon service representative.

SCANNER ERROR

Make sure that the protective material is removed from the FINE Cartridge Holder, then turn the machine off and back on again. If the problem is not resolved, contact your Canon Service representative.

An Error Code Is Displayed on the LED (MP210 series)

Alarm Lamp is lit Orange

When a printer error occurs, the Alarm lamp is lit orange. The number displayed on the LED indicates the type of error that has occurred. Check the error code displayed on the LED and take the appropriate action to correct the error.

E and number (error code) are alternately displayed on the LED of MP210 series.

Error Code

Cause

Action

E, 2

The machine is out of paper. / Paper does not feed.

Reload the paper correctly and press the Black or Color button.

E, 3

Paper jam.

If paper has jammed in the machine, clear the jam, reload the paper in the machine correctly and then press the Black or Color button.

E, 4/

E, 5

The FINE Cartridge cannot be recognized.

The FINE Cartridge may not be installed properly, or the Cartridge may not be compatible with this machine. Open the Scanning Unit (Printer Cover) and install the appropriate FINE Cartridge.

If the error is not resolved, the Print Head may be damaged. Contact your Canon Service representative.

E, 7

FINE Cartridge is not installed in the correct position.

Make sure that each FINE Cartridge is installed in the correct position.

See Replacing a FINE Cartridge.

E, 8

Ink absorber is almost full.

The machine has a built-in ink absorber to hold the ink used during Print Head Cleaning, for example.

This error code indicates that the ink absorber is nearly full.

Press the Black or Color button to cancel the error so you can continue printing.

However, because printing is disabled once the ink absorber becomes completely full and until the ink absorber is replaced, you are recommended to contact your Canon service representative as early as possible. (You will need to replace a particular part of the machine.)

E, 9

The digital camera or digital video camcorder connected is not compatible with this machine.

A communication time out occurs if an operation takes too long or if it takes too much time to send data. This may cancel printing. In such cases, disconnect and reconnect the USB cable.

When printing from a PictBridge compliant device, depending on the model or brand of your device, you may have to select a PictBridge compliant print mode on the device before connecting it to the machine. You may also have to turn on your device or select Play mode manually after connecting the device to the machine. Perform necessary operations before connecting your device referring to its instruction manual.

If the error is still not resolved, check if you can print another photograph.

E, 1, 3

Ink level cannot be detected.

Ink may have run out.

The function for detecting the remaining ink level will be disabled since the ink level cannot be correctly detected.

If you want to continue printing without this function, press the Stop/Reset button for at least 5 seconds.

Canon recommends to use new genuine Canon cartridges in order to obtain optimum qualities.

Please be advised that Canon shall not be liable for any malfunction or trouble caused by continuation of printing under the ink out condition.

E, 1, 4

The FINE Cartridge cannot be recognized.

The FINE Cartridge may not be compatible with this machine. Install the appropriate FINE Cartridge. See Replacing a FINE Cartridge.

E, 1, 5

The FINE Cartridge cannot be recognized.

The FINE Cartridge may not be installed properly.

Open the Scanning Unit (Printer Cover) and install the FINE Cartridge properly.

If the error is not resolved, the FINE Cartridge may be damaged. Contact your Canon Service representative.

E, 1, 6

Ink has run out.

Ink has run out.

Replace the ink cartridge and close the Scanning Unit (Printer Cover).

If printing is in progress and you want to continue printing, press the Stop/Reset button for at least 5 seconds with the ink cartridge installed. Then printing can continue under the ink out condition.

The function for detecting the remaining ink level will be disabled.

Replace the empty ink cartridge immediately after the printing. The resulting print quality is not satisfactory, if printing is continued under the ink out condition.

E, 1, 9

PictBridge compliant device is connected via a USB hub.

If a PictBridge compliant device is connected via a USB hub, remove the hub and connect it directly to the machine.

E, 2, 0

The size of the document cannot be correctly detected or the document is too small when the Fit-to-Page copying is selected. / Scanning the Print Head Alignment Sheet has failed.

The size of the document cannot be correctly detected or the document is too small when the Fit-to-Page copying is selected.

Make sure the document meets the requirements and correctly loaded on the Platen Glass. Then reload the document and press the Black or Color button.

See Loading Original Documents.

Scanning the Print Head Alignment Sheet has failed. Make sure all required boxes on the head alignment sheet are filled in, and that the sheet is set in the correct position and orientation on the Platen Glass.

If the error is not resolved, connect the machine to the computer and align the Print Head on the printer driver. For details, see Aligning Print Head on the Computer.

Power Lamp Flashes Green and Alarm Lamp Flashes Orange Alternately

The Power and Alarm lamps flash alternately as shown below.

Disconnect the USB cable from the machine, turn the machine off, and then unplug the machine from the power supply. Plug the machine back in and turn the machine back on after leaving it for a while.

If the problem is not resolved, contact your Canon Service representative.

Error Code

Cause

Action

E, 2, x

E, 3, x

E, 4, x

An error requiring servicing might have occurred.

Make sure that the protective material is removed from the FINE Cartridge Holder, then turn the machine off and unplug the power cord of the machine from the power supply. After a while, plug the power cord of the machine back in, and then turn on the machine. If the same error occurs, contact your Canon service representative.


   În speranţa că informaţiile mele v-au fost utile şi vă urez Succes şi la cît mai puţine coduri E 5 că E-urile nu sînt bune nici în mîncare.

 
Google